Home > Mobile >  What are the various ways to disable and re-enable interrupts in STM32 microcontrollers in order to
What are the various ways to disable and re-enable interrupts in STM32 microcontrollers in order to

Time:03-27

The standard technique to enforce atomic access to volatile variables shared with ISRs, via "atomic access guards" or "interrupt guards", is as follows:

// 1. save interrupt state
// 2. disable only the interrupts necessary

// you get atomic access to volatile variables shared with ISRs here

// 3. restore interrupt state

See also where I describe this in detail here, including best practices (keep interrupts off for short period of time) and how to do atomic reads withOUT disabling interrupts first, via my doAtomicRead() repeat-read-loop function: Reading a 64 bit variable that is updated by an ISR.

I have previously documented how to do this for AVR microcontrollers/Arduino: How do I force atomicity in Atmel AVR mcus/Arduino?.

But, how do I do this for STM32 microcontrollers? I know there are a lot of ways.

Please cover the following techniques:

  1. Via ARM-core CMSIS:
    1. for global interrupts
    2. for specific IRQs (Interrupt Requests)
  2. Via STM32 HAL (Hardware Abstraction Layer)
  3. Via FreeRTOS

This answer is related, but insufficient: How can I re-enable the stm32f103's external interrupt after I disable it?

CodePudding user response:

You have made a false assertion in your question so that you can post your own answer that presumes the false assertion.

The standard way to have atomic access to shared variables is absolutely not to turn interrupts off.

This was a widespread technique in the 1990s and earlier, but for all mainstream microcontrollers developed from the early 2000s this is bad advice in general. I have professional engineers in my department who were not even born yet when your advice was out of date!

In all but the most basic of projects, atomic access should be achieved using LDREX/STREX exclusive access instructions. Complex message queues and semaphore systems can be built upon these primitives which do not ever require to disable interrupts.

Disabling interrupts increases the latency of the system in ways which are difficult to predict, and should be avoided wherever possible.

CodePudding user response:

Multiple ways to enable/disable interrupts in STM32 mcus:

1. Via ARM-core CMSIS:

A. For global interrupts

__enable_irq()   // enable all interrupts
__disable_irq()  // disable all interrupts

// Returns the current state of the priority mask bit from the Priority Mask
// Register. [0 if global interrupts are **enabled** and non-zero if they
// are **disabled**]
__get_PRIMASK()

For the definition of these functions, see:

  1. https://github.com/ARM-software/CMSIS/blob/master/CMSIS/Include/cmsis_gcc.h
    1. Contains at least:
      __enable_irq() 
      __disable_irq()
      __get_PRIMASK()
      __set_PRIMASK()
      
  2. STM32 example location: "stm/stm32f2xx/st_hal_v1.1.3/CMSIS/Include/cmsis_gcc.h":

To save and restore the interrupt state, use __get_PRIMASK(), like this:

// 1. back up interrupt state; `__get_PRIMASK()` returns 0 if interrupts
// are **enabled**, and non-zero if they are **disabled**.
bool interrupts_enabled = (__get_PRIMASK() == 0);

// do stuff

// 2. Disable interrupts
__disable_irq();
// 3. Restore backed-up-state
if (interrupts_enabled) {
    __enable_irq();
}

When dealing with global interrupts, this is the best way for bare-metal, non-FreeRTOS code!

I think this technique is also cross-compatible with ALL ARM-core mcus, not just STM32.

I first learned this technique from Tilen Majerle, here: https://stm32f4-discovery.net/2015/06/how-to-properly-enabledisable-interrupts-in-arm-cortex-m/. His work and contributions to clear up this super-obfuscated stuff are infinitely valuable and appreciated!

His example:

void ImportantFunction1(void) {
    /* Important function 1 */
    uint32_t prim;
    
    /* Do some stuff here which can be interrupted */
    
    /* Read PRIMASK register, check interrupt status before you disable them */
    /* Returns 0 if they are enabled, or non-zero if disabled */
    prim = __get_PRIMASK();
    
    /* Disable interrupts */
    __disable_irq();
    
    /* Do some stuff here which can not be interrupted */
    
    /* Call subfunction */
    ImportantFunction2();
    
    /* Do some stuff here which can not be interrupted */
    /* This part is still interrupt safe because ImportantFunction2 will not enable interrupts */
    
    /* Enable interrupts back */
    if (!prim) {
        __enable_irq();
    }
    
    /* Do some stuff here which can be interrupted */
}

B. For specific IRQs (Interrupt Requests)

It is best to avoid disabling global interrupts, if possible, and disable only the fewest number of specific interrupts possible to achieve atomicity for your specific code. So, using these functions allows you to enable or disable only the specific interrupts you need to!

Enable or disable specific types of interrupts:

void NVIC_EnableIRQ(IRQn_Type IRQn);
void NVIC_DisableIRQ(IRQn_Type IRQn);

NVIC stands for "Nested Vector Interrupt Controller". Nested interrupts (meaning: a higher-priority interrupt can still fire within an ISR) are enabled by default on STM32 microcontrollers. Each interrupt type has a priority assigned to it, with lower priority numbers being higher priority, and higher-priority interrupts are able to fire while an ISR is being processed for a lower-priority interrupt. See here for a little more information on the STM32 NVIC: https://stm32f4-discovery.net/2014/05/stm32f4-stm32f429-nvic-or-nested-vector-interrupt-controller/.

Contrast this to AVR microcontrollers (ex: ATMega328 / Arduino Uno), which do not have priority-based interrupts, so by default, when any ISR is being processed, all interrupts (ie: global interrupts) are automatically disabled as the program enters the ISR. Note that even on AVR mcus, however, you can still manually enable nested interrupts / ISRs if you like by manually re-enabling global interrupts inside your ISR, via a call to interrupts() on Arduino or sei() (set interrupts) on raw AVR.

Each ARM-core microcontroller manufacturer, I believe, including STM32 types, must define and create its own list of IRQn_Type interrupt request types, so see below for the STM32 details on their specific interrupt types defined for each mcu.

2. Via STM32 HAL (Hardware Abstraction Layer) libraries

Enable or disable specific types of interrupts:

// enable interrupts
HAL_NVIC_EnableIRQ(IRQn_Type IRQn);
// disable interrupts 
HAL_NVIC_DisableIRQ(IRQn_Type IRQn);

See, for example: "stm/stm32f2xx/st_hal_v1.1.3/STM32F2xx_HAL_Driver/Src/stm32f2xx_hal_cortex.c/.h" - definitions for those functions above are in those files. See them online:

  1. https://github.com/STMicroelectronics/STM32CubeF2/blob/master/Drivers/STM32F2xx_HAL_Driver/Inc/stm32f2xx_hal_cortex.h#L264-L265
  2. https://github.com/STMicroelectronics/STM32CubeF2/blob/master/Drivers/STM32F2xx_HAL_Driver/Src/stm32f2xx_hal_cortex.c#L178-L210

Here are the definitions of HAL_NVIC_EnableIRQ() and HAL_NVIC_DisableIRQ(). Notice that they just check to ensure your IRQn is valid, then they pass the input argument on to the ARM-core CMSIS NVIC_EnableIRQ() and NVIC_DisableIRQ() functions above!:

/**
  * @brief  Enables a device specific interrupt in the NVIC interrupt controller.
  * @note   To configure interrupts priority correctly, the NVIC_PriorityGroupConfig()
  *         function should be called before. 
  * @param  IRQn External interrupt number.
  *         This parameter can be an enumerator of IRQn_Type enumeration
  *         (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f2xxxx.h))
  * @retval None
  */
void HAL_NVIC_EnableIRQ(IRQn_Type IRQn)
{
  /* Check the parameters */
  assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
  
  /* Enable interrupt */
  NVIC_EnableIRQ(IRQn);
}

/**
  * @brief  Disables a device specific interrupt in the NVIC interrupt controller.
  * @param  IRQn External interrupt number.
  *         This parameter can be an enumerator of IRQn_Type enumeration
  *         (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f2xxxx.h))
  * @retval None
  */
void HAL_NVIC_DisableIRQ(IRQn_Type IRQn)
{
  /* Check the parameters */
  assert_param(IS_NVIC_DEVICE_IRQ(IRQn));
  
  /* Disable interrupt */
  NVIC_DisableIRQ(IRQn);
}

For IRQn_Types: see the appropriate definition file for your specific board! These are board-specific definitions, for your board from your manufacturer. Here are all of the boards in the STM32 F2xx line, for instance: https://github.com/STMicroelectronics/STM32CubeF2/tree/master/Drivers/CMSIS/Device/ST/STM32F2xx/Include. Let's look at the stm32f217xx.h file specifically:

  1. https://github.com/STMicroelectronics/STM32CubeF2/blob/master/Drivers/CMSIS/Device/ST/STM32F2xx/Include/stm32f217xx.h
  2. Raw view (since file is too big to view on GitHub otherwise): https://raw.githubusercontent.com/STMicroelectronics/STM32CubeF2/master/Drivers/CMSIS/Device/ST/STM32F2xx/Include/stm32f217xx.h

From this file, we can see the typedef enum definition for the IRQn_Type, which is the "STM32F2XX Interrupt Number Definition". Here is what it looks like:

/**
 * @brief STM32F2XX Interrupt Number Definition, according to the selected device 
 *        in @ref Library_configuration_section 
 */
typedef enum
{
/******  Cortex-M3 Processor Exceptions Numbers ****************************************************************/
  NonMaskableInt_IRQn         = -14,    /*!< 2 Non Maskable Interrupt                                          */
  HardFault_IRQn              = -13,    /*!< 3 Hard Fault Interrupt                                            */
  MemoryManagement_IRQn       = -12,    /*!< 4 Cortex-M3 Memory Management Interrupt                           */
  BusFault_IRQn               = -11,    /*!< 5 Cortex-M3 Bus Fault Interrupt                                   */
  UsageFault_IRQn             = -10,    /*!< 6 Cortex-M3 Usage Fault Interrupt                                 */
  SVCall_IRQn                 = -5,     /*!< 11 Cortex-M3 SV Call Interrupt                                    */
  DebugMonitor_IRQn           = -4,     /*!< 12 Cortex-M3 Debug Monitor Interrupt                              */
  PendSV_IRQn                 = -2,     /*!< 14 Cortex-M3 Pend SV Interrupt                                    */
  SysTick_IRQn                = -1,     /*!< 15 Cortex-M3 System Tick Interrupt                                */
/******  STM32 specific Interrupt Numbers **********************************************************************/
  WWDG_IRQn                   = 0,      /*!< Window WatchDog Interrupt                                         */
  PVD_IRQn                    = 1,      /*!< PVD through EXTI Line detection Interrupt                         */
  TAMP_STAMP_IRQn             = 2,      /*!< Tamper and TimeStamp interrupts through the EXTI line             */
  RTC_WKUP_IRQn               = 3,      /*!< RTC Wakeup interrupt through the EXTI line                        */
  FLASH_IRQn                  = 4,      /*!< FLASH global Interrupt                                            */
  RCC_IRQn                    = 5,      /*!< RCC global Interrupt                                              */
  EXTI0_IRQn                  = 6,      /*!< EXTI Line0 Interrupt                                              */
  EXTI1_IRQn                  = 7,      /*!< EXTI Line1 Interrupt                                              */
  EXTI2_IRQn                  = 8,      /*!< EXTI Line2 Interrupt                                              */
  EXTI3_IRQn                  = 9,      /*!< EXTI Line3 Interrupt                                              */
  EXTI4_IRQn                  = 10,     /*!< EXTI Line4 Interrupt                                              */
  DMA1_Stream0_IRQn           = 11,     /*!< DMA1 Stream 0 global Interrupt                                    */
  DMA1_Stream1_IRQn           = 12,     /*!< DMA1 Stream 1 global Interrupt                                    */
  DMA1_Stream2_IRQn           = 13,     /*!< DMA1 Stream 2 global Interrupt                                    */
  DMA1_Stream3_IRQn           = 14,     /*!< DMA1 Stream 3 global Interrupt                                    */
  DMA1_Stream4_IRQn           = 15,     /*!< DMA1 Stream 4 global Interrupt                                    */
  DMA1_Stream5_IRQn           = 16,     /*!< DMA1 Stream 5 global Interrupt                                    */
  DMA1_Stream6_IRQn           = 17,     /*!< DMA1 Stream 6 global Interrupt                                    */
  ADC_IRQn                    = 18,     /*!< ADC1, ADC2 and ADC3 global Interrupts                             */
  CAN1_TX_IRQn                = 19,     /*!< CAN1 TX Interrupt                                                 */
  CAN1_RX0_IRQn               = 20,     /*!< CAN1 RX0 Interrupt                                                */
  CAN1_RX1_IRQn               = 21,     /*!< CAN1 RX1 Interrupt                                                */
  CAN1_SCE_IRQn               = 22,     /*!< CAN1 SCE Interrupt                                                */
  EXTI9_5_IRQn                = 23,     /*!< External Line[9:5] Interrupts                                     */
  TIM1_BRK_TIM9_IRQn          = 24,     /*!< TIM1 Break interrupt and TIM9 global interrupt                    */
  TIM1_UP_TIM10_IRQn          = 25,     /*!< TIM1 Update Interrupt and TIM10 global interrupt                  */
  TIM1_TRG_COM_TIM11_IRQn     = 26,     /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */
  TIM1_CC_IRQn                = 27,     /*!< TIM1 Capture Compare Interrupt                                    */
  TIM2_IRQn                   = 28,     /*!< TIM2 global Interrupt                                             */
  TIM3_IRQn                   = 29,     /*!< TIM3 global Interrupt                                             */
  TIM4_IRQn                   = 30,     /*!< TIM4 global Interrupt                                             */
  I2C1_EV_IRQn                = 31,     /*!< I2C1 Event Interrupt                                              */
  I2C1_ER_IRQn                = 32,     /*!< I2C1 Error Interrupt                                              */
  I2C2_EV_IRQn                = 33,     /*!< I2C2 Event Interrupt                                              */
  I2C2_ER_IRQn                = 34,     /*!< I2C2 Error Interrupt                                              */  
  SPI1_IRQn                   = 35,     /*!< SPI1 global Interrupt                                             */
  SPI2_IRQn                   = 36,     /*!< SPI2 global Interrupt                                             */
  USART1_IRQn                 = 37,     /*!< USART1 global Interrupt                                           */
  USART2_IRQn                 = 38,     /*!< USART2 global Interrupt                                           */
  USART3_IRQn                 = 39,     /*!< USART3 global Interrupt                                           */
  EXTI15_10_IRQn              = 40,     /*!< External Line[15:10] Interrupts                                   */
  RTC_Alarm_IRQn              = 41,     /*!< RTC Alarm (A and B) through EXTI Line Interrupt                   */
  OTG_FS_WKUP_IRQn            = 42,     /*!< USB OTG FS Wakeup through EXTI line interrupt                     */    
  TIM8_BRK_TIM12_IRQn         = 43,     /*!< TIM8 Break Interrupt and TIM12 global interrupt                   */
  TIM8_UP_TIM13_IRQn          = 44,     /*!< TIM8 Update Interrupt and TIM13 global interrupt                  */
  TIM8_TRG_COM_TIM14_IRQn     = 45,     /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */
  TIM8_CC_IRQn                = 46,     /*!< TIM8 Capture Compare Interrupt                                    */
  DMA1_Stream7_IRQn           = 47,     /*!< DMA1 Stream7 Interrupt                                            */
  FSMC_IRQn                   = 48,     /*!< FSMC global Interrupt                                             */
  SDIO_IRQn                   = 49,     /*!< SDIO global Interrupt                                             */
  TIM5_IRQn                   = 50,     /*!< TIM5 global Interrupt                                             */
  SPI3_IRQn                   = 51,     /*!< SPI3 global Interrupt                                             */
  UART4_IRQn                  = 52,     /*!< UART4 global Interrupt                                            */
  UART5_IRQn                  = 53,     /*!< UART5 global Interrupt                                            */
  TIM6_DAC_IRQn               = 54,     /*!< TIM6 global and DAC1&2 underrun error  interrupts                 */
  TIM7_IRQn                   = 55,     /*!< TIM7 global interrupt                                             */
  DMA2_Stream0_IRQn           = 56,     /*!< DMA2 Stream 0 global Interrupt                                    */
  DMA2_Stream1_IRQn           = 57,     /*!< DMA2 Stream 1 global Interrupt                                    */
  DMA2_Stream2_IRQn           = 58,     /*!< DMA2 Stream 2 global Interrupt                                    */
  DMA2_Stream3_IRQn           = 59,     /*!< DMA2 Stream 3 global Interrupt                                    */
  DMA2_Stream4_IRQn           = 60,     /*!< DMA2 Stream 4 global Interrupt                                    */
  ETH_IRQn                    = 61,     /*!< Ethernet global Interrupt                                         */
  ETH_WKUP_IRQn               = 62,     /*!< Ethernet Wakeup through EXTI line Interrupt                       */
  CAN2_TX_IRQn                = 63,     /*!< CAN2 TX Interrupt                                                 */
  CAN2_RX0_IRQn               = 64,     /*!< CAN2 RX0 Interrupt                                                */
  CAN2_RX1_IRQn               = 65,     /*!< CAN2 RX1 Interrupt                                                */
  CAN2_SCE_IRQn               = 66,     /*!< CAN2 SCE Interrupt                                                */
  OTG_FS_IRQn                 = 67,     /*!< USB OTG FS global Interrupt                                       */
  DMA2_Stream5_IRQn           = 68,     /*!< DMA2 Stream 5 global interrupt                                    */
  DMA2_Stream6_IRQn           = 69,     /*!< DMA2 Stream 6 global interrupt                                    */
  DMA2_Stream7_IRQn           = 70,     /*!< DMA2 Stream 7 global interrupt                                    */
  USART6_IRQn                 = 71,     /*!< USART6 global interrupt                                           */
  I2C3_EV_IRQn                = 72,     /*!< I2C3 event interrupt                                              */
  I2C3_ER_IRQn                = 73,     /*!< I2C3 error interrupt                                              */
  OTG_HS_EP1_OUT_IRQn         = 74,     /*!< USB OTG HS End Point 1 Out global interrupt                       */
  OTG_HS_EP1_IN_IRQn          = 75,     /*!< USB OTG HS End Point 1 In global interrupt                        */
  OTG_HS_WKUP_IRQn            = 76,     /*!< USB OTG HS Wakeup through EXTI interrupt                          */
  OTG_HS_IRQn                 = 77,     /*!< USB OTG HS global interrupt                                       */
  DCMI_IRQn                   = 78,     /*!< DCMI global interrupt                                             */
  CRYP_IRQn                   = 79,     /*!< CRYP crypto global interrupt                                      */
  HASH_RNG_IRQn               = 80      /*!< Hash and Rng global interrupt                                     */
} IRQn_Type;

Example usage using STM32 HAL:

To get exclusive access (to ensure strings are atomically printed, for instance) to the USART1 for printing debug chars via a HAL-based blocking (polled) mode (ie: via HAL_UART_Transmit()), you need to disable all interrupts for USART1_IRQn by doing the following. (This guarantees you get atomic access to this device):

// 1. Disable the UART IRQ
HAL_NVIC_DisableIRQ(USART1_IRQn);

// 2. Send your string (in HAL blocking/polled mode)
// Prototype for this function is from 
// "...stm/stm32f7xx/st_hal_v1.1.2/STM32F7xx_HAL_Driver/Src/stm32f7xx_hal_uart.c": 
// - `HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, 
//        uint8_t *pData, uint16_t Size, uint32_t Timeout)`
// Note: `huart` is defined by STM32CubeMX as `UART_HandleTypeDef huart1;` 
// in "hal_source/Src/usart.c"
HAL_UART_Transmit(&huart1, (uint8_t *)my_str, strlen(my_str), HAL_MAX_DELAY);

// 3. Enable the UART_IRQ
// FUTURE WORK: make this nestable/more robust by only enabling the 
// IRQ here if it was previously enabled before disabling it!
HAL_NVIC_EnableIRQ(USART1_IRQn);

3. Via FreeRTOS:

The FreeRTOS atomic-access-guard / interrupt-related functions are listed under the "Modules" section of the Kernel Control API here: Kernel Control:

taskYIELD()
taskENTER_CRITICAL()            // interrupts off
taskEXIT_CRITICAL()             // restore interrupts
taskENTER_CRITICAL_FROM_ISR()   // interrupts off
taskEXIT_CRITICAL_FROM_ISR()    // restore interrupts
taskDISABLE_INTERRUPTS()        // interrupts off
taskENABLE_INTERRUPTS()         // interrupts on

A. Higher-level macros:

  1. These are the preferred macros to use, and are the freertos-recommended ones!
  2. These all support nested calls, and end up calling portDISABLE_INTERRUPTS() anyway, which is the port implementation of the lower-level taskDISABLE_INTERRUPTS(), shown below.
  3. From: https://www.freertos.org/taskENTER_CRITICAL_taskEXIT_CRITICAL.html
    taskENTER_CRITICAL()        // interrupts off
    taskEXIT_CRITICAL()         // restore interrupts
    
  4. From: https://www.freertos.org/taskENTER_CRITICAL_FROM_ISR_taskEXIT_CRITICAL_FROM_ISR.html
    taskENTER_CRITICAL_FROM_ISR()
    taskEXIT_CRITICAL_FROM_ISR()
    

B. Lower-level macros:

  1. These do NOT support nested calls!

  2. Official documentation on them is on the main "Kernel Control" page:

    taskDISABLE_INTERRUPTS()
    taskENABLE_INTERRUPTS()
    
  3. Notes and limiatations:

    1. taskDISABLE_INTERRUPTS() at the link above states:

    Normally this macro would not be called directly and taskENTER_CRITICAL() and taskEXIT_CRITICAL() should be used in its place.

    1. taskENABLE_INTERRUPTS() at the link above states:

    Normally this macro would not be called directly and taskENTER_CRITICAL() and taskEXIT_CRITICAL() should be used in its place.

    1. Note also that the use of taskDISABLE_INTERRUPTS() is demonstrated as the technique used to panic inside an example macro definition for configASSERT().
      1. From here: https://www.freertos.org/a00110.html#configASSERT, when used with a debugger, it is defined as:
        /* Define configASSERT() to disable interrupts and sit in a loop. */
        #define configASSERT( ( x ) )     if( ( x ) == 0 ) { taskDISABLE_INTERRUPTS(); for( ;; ); }
        
      2. My thoughts: perhaps in this one case (ie: hard asserting, or panicking), taskDISABLE_INTERRUPTS() might be preferred over taskENTER_CRITICAL() because no amount of calling taskEXIT_CRITICAL() from another thread will re-enable interrupts once taskDISABLE_INTERRUPTS() has been called [I think!?]--rather, one would have to explicitly (and accidentally) call taskENABLE_INTERRUPTS() (ex: from another thread) to re-enable interrupts once taskDISABLE_INTERRUPTS() has been called. In other words, using the low-level taskDISABLE_INTERRUPTS() call is appropriate here because it will truly cause the system to sit in a loop, as desired, whereas taskENTER_CRITICAL() would not.

Mutexes and other OS (Operating System)-enabled synchronization primitives

Beyond the examples above, you can also use FreeRTOS queues (which are thread-safe, unlike all containers in the C std library), mutexes, semaphores, task notifications, and other synchronization primitives, where able and where appropriate, to protect certain data which is shared between FreeRTOS tasks (threads), assuming you are running FreeRTOS.

See the list of these tools here: https://www.freertos.org/a00106.html, and in the left-hand navigation menus once you click on that link.

See also:

  1. My answer on this for AVR mcus/Arduino
  2. My answer on the general practice and demo of using atomic access guards, and my doAtomicRead() func which ensures atomic access withOUT turning interrupts off
  3. [my Q&A] Which variable types/sizes are atomic on STM32 microcontrollers?
  • Related