The great god good:
#
#./hostapd/MNT/hostapd. Conf
The Configuration file:/MNT/hostapd. Conf
The ioctl [PRISM2_IOCTL_PRISM2_PARAM] : Bad address
Could not enable hostapd mode for interface wlan0
Hostap driver initialization failed.
Wlan0: interface state UNINITIALIZED - & gt; DISABLED
Wlan0: AP - DISABLED
Hostapd_free_hapd_data: Interface wlan0 wasn 't started

After the above is my cross compiling hostapd, switching wi-fi chips with hostapd tools to ap mode, the problem of wifi chip for rtl8188ftv, also the great god, please help, thank you,
When compiling hostapd CONFIG_DRIVER_NL80211=y that I did not open, use CONFIG_DRIVER_HOSTAP=y; My hostapd. Conf configuration is as follows:

Interface=wlan0
# driver=8188 fu
Ssid=hostapdTest
The channel=1
Hw_mode=g
Auth_algs=1
Ignore_broadcast_ssid=0
Ctrl_interface_group=0
Wpa=3
Wpa_passphrase=12345678
Wpa_key_mgmt=WPA wpa2-psk
Wpa_pairwise=TKIP
# ieee80211n=1

CodePudding user response:

Behind the building without success? Sorry, CSDN sentiment so bad now?

CodePudding user response:

1/f, reference path from technology to management response:

behind the building without success? Sorry, CSDN sentiment so bad now?

Level is so high also dug grave ~

CodePudding user response:

refer to the second floor LubinLew response:

Quote: refer to 1st floor from technology to manage the road response:

Behind the building without success? Sorry, CSDN sentiment so bad now?

Level is so high also dug grave ~

Ha, ha, ha, I was looking at this BBS is so downfallen, send a question nobody reply, these people were run where go to, don't need to communicate, I remember that during 2008 ~ 2012 BBS can be noisy,

CodePudding user response:

reference 3 floor from technology to manage the road response:

Quote: refer to the second floor LubinLew response:

Quote: 1/f, reference path from technology to management response:

Behind the building without success? Sorry, CSDN sentiment so bad now?

Level is so high also dug grave ~

Ha, ha, ha, I was looking at this BBS is so downfallen, send a question nobody reply, these people were run where go to, don't need to communicate, I remember that during 2008 ~ 2012 BBS can be noisy,

Too few people, most of them are problems immediately registered an account, a matter of not reply post. Always hot face against cold ass, time is long is not willing to answer this question

CodePudding user response:

LubinLew

reference 4 floor response:

Quote: refer to the third floor from technology to management road reply:

Quote: refer to the second floor LubinLew response:

Quote: 1/f, reference path from technology to management response:

Behind the building without success? Sorry, CSDN sentiment so bad now?

Level is so high also dug grave ~

Ha, ha, ha, I was looking at this BBS is so downfallen, send a question nobody reply, these people were run where go to, don't need to communicate, I remember that during 2008 ~ 2012 BBS can be noisy,

Too few people, most of them are problems immediately registered an account, a matter of not reply post. Always hot face against cold ass, time is long is not willing to answer questions

Mainly times have changed, you don't like BBS communication, a lot of people just want to ask for, not answer, also all kinds of feeling bad, answer, and then not then,

CodePudding user response:

The building Lord Could not enable hostapd mode for interface wlan0
Hostap driver initialization failed.
Wlan0: interface state UNINITIALIZED - & gt; DISABLED this problem I met, let me answer, this basically is not closed wlan0, want to shut down first, set up and udhcpd. Conf the same IP, won't appear the error,

CodePudding user response:

1, using the driver from Realtek RTL8188EUS_linux_v5. 3.9 _28540. 20180806. Zip package.
2, the download wpa_supplicant - v2.7 and hostapd - v2.7 from http://w1.fi/
3, in hostapd, you must enable the nl82011 driver support.

4, the Realtek FTP server is:

ftp://ftp3.realtek.com

User: RTL8188E
Passwd: M6b3Er

(8818 eus/ETV/es 8189)

PS: the newest driver support is 5.7.6.1, you may test it if you like