Technology bosses hello:

One project of tunnel in local network (has to form a ring) equipment for 487, the early stage of the design for 192.168.0.1-254/C 255.255.252.0, 192.168.1.1-254/255.255.252.0,

After remaining 192.168.2.1-254/255.255.252.0 192.168.3.1-254/255.255.252.0

And the host position with h3c switches on the second floor and through the router connected to the corporate Intranet

Now met prior to the construction of the second phase of equipment 620, number of leak caused segment,

Now need several programs can facilitate the timely solve such problems

1, such as modified early 487 devices before modifying the subnet mask of 248 (volume)
2, increase the layer 3 switches divide Vlan on each segment of independent management, do not need to modify the subnet mask (layer 3 switches configuration that needs to be purchased) (to prevent broadcast storm)
3, the second phase of equipment using other segment separate separate, not connected to a phase of the project network
4, other alternative

What kind of solution is more effective more

Thanks for the great spirit support, thank you

CodePudding user response:

Give a diagram? What kind of tunnel is tunnel? I think don't need to add and change anything, you see the single-arm routing information online, and see if I can meet your demand,

CodePudding user response:

22 mask is inherently support 1000 IP, 192.168.0.1/22, and 192.168.1.1/22, 192.168.2.1/22192168. 3.1/22 are on a network segment, so use 192.168.2.1 255.255.252.0

CodePudding user response:

Is wrong and has been used up, then went on a three layer devices, but so many devices in a vlan, will have a problem

CodePudding user response:

Is now the number of equipment is beyond the 1000 IP, there are separate vlans, if all have to add routing implementation, problems may arise during

CodePudding user response:

So I want to see your topology, look at your hundreds of machine what is the use of layer 2 switches? Layer 2 switches and routers is how even again,

CodePudding user response:

Network topology is not around now, tunnel structure for optical fiber double loop network, is the ring net switch with the lower sensor camera equipment, through the ring net switch between h3c switches, optical fiber transmission into master station in through a small router wan port distribution network access to the Intranet,

CodePudding user response:

Personal feel better with the method of the VLAN

CodePudding user response:

192.168.0.1 gateway where are you located in? To exchange of visits between these devices? The router wan mouth? Isn't that a router is a few blocks, eighty pieces of router? Can be set up? Located in the router 192.168.0.1?

CodePudding user response:

Require visits, ha ha yes small version of the tp cc-link 192.168.0.1 a gateway is set on it, the wan port distribution network IP address, useless huawei cisco routers, switches or 2 h3c

CodePudding user response:

If the router can set the vlan, such as virtual so ah, so you can use the single-arm routing way, but should pay attention to the broadcast storm, the second is the best way of solution, in a layer 3 switches, but you mentioned the ring net switch, should set up a vlan, to avoid the broadcast storm,

In addition, the network of the tunnel met, but don't know, whether the equipment you far away from the computer room, so want to use the network?

CodePudding user response:

Change a mask, to mobilize the user it ourselves

CodePudding user response:

Yes ring net switch is have no lton-us period of communication, far, about 10 km, double loop network is optical fiber network, Internet has so far

CodePudding user response:

refer to 12 floor weixin_42968177 reply:

yes ring net switch is have no lton-us period of communication, far, about 10 km, double loop network is optical fiber network, Internet has so far

Our unit is also used in the tunnel network, but is of the construction of the telecommunications, so only know principle, did not match in person, however, your side of the tunnel is the first camera sensor, also should have other switches, would not be so devices are directly connected to the ring net switch?