PCB industry trend
1, the whole of China PCB industry booming
Since China's reform and opening up, Chinese because in labor resources, market, investment and other aspects of preferential policies to attract the mass transfer of manufacturing industry in Europe and America, a large number of electronic products and manufacturers will factory set up in China, and thus led to the development of related industries, including PCB, according to the Chinese CPCA statistics, in 2006 China has reached 130 million square meters, PCB production actual output value reached $12.1 billion, accounting for 24.90% of global PCB output, more than Japan to become the world's first, from 2000 to 2006, the Chinese PCB market average annual growth rate of 20%, far more than the global average, the global financial crisis in 2008 caused a huge impact to the PCB industry, but not catastrophic blow to China's PCB industry, under the country's economic stimulus in 2010 appeared a full recovery, China's PCB industry output value as high as $19.971 billion, 2010 China PCB Prismark forecast 2010-2015 China would maintain the compound average annual growth rate of 8.10%, higher than the growth rate of 5.40% of the world's average,
2, industry regional distribution imbalance
The PCB industry in China are mainly distributed south China and east China region, combined amounted to 90% of the country, the industrial cluster effect obviously, this phenomenon is mainly with the main production base of China's electronics industry is concentrated in the pearl river delta, Yangtze river delta,
3, China's PCB industry downstream application distribution
China's PCB industry downstream distribution are shown in the figure below, the consumer electronics accounted for the highest, at 39%; Followed by the computer, accounting for 22%; Communication (14%); Industrial control/medical instruments accounted for 14%; Automotive electronics (6%); Defense and aerospace (5%),
4, technical development lags behind the advanced level
China now although from industry scale has been the world's first, in terms of the overall technical level, but from the PCB industry still lags behind the advanced level, on the product structure, laminated occupied most of output value proportion, but most of them 8 layer below the low-end products, HDI, flexible plate and so on has the certain scale but on the technical gap with Japan and other advanced foreign products, the highest technical content among IC loading board in domestic few enterprises can produce more,
PCB industry status quo of
Benefit from the new products and new market terminal take turns to support, global PCB market successful recovery and growth, the circuit board association of Hong Kong (HKPCA) data statistics, in 2011 the global PCB market steady development, is expected to rise of 6-9%, while China is expected to grow 9-12%, Taiwan industry research institute (IEK)? Analysis predicts that global PCB GDP will grow by 10.36% in 2011, the scale of up to $41.615 billion, according to the analysis of data and Prismark company societe generale securities research center report shows that the PCB change of structure and product structure reflects the trend of the development of industry, with single/double panel, sandwich plate decline in output, HDI board, sealing load board, soft board output increase, that applied to computer motherboards, communication backplane, car plate in the areas of growth is slower, and applied to high-end phones, laptops and other "lightweight" HDI board of electronic products, packaging board and soft board will also maintain rapid growth,
North American
Printed circuit association (IPC) released in the United States, North America in February 2011, the overall printed circuit board manufacturers orders and billing than (the book - to - bill thewire) is 0.95, means that the product shipment per $100 during the month only received $95 worth of new orders, B/B value for the fifth consecutive month less than 1, the boom of north American industry had substantial rebound,
Japan
Part, the Japanese earthquake short-term impact PCB raw material supply, long-term benefit capacity to Taiwan and the mainland, high-end PCB manufacturers to accelerate the expansion of the mainland, technology, production capacity and order transfer to mainland China is the trend of The Times, when the electronic newspaper reported that Taiwan supply chain in Japan, China, South Korea PCB factory will be a big winner
Taiwan
Taiwan institute (IEK) analysts point out that benefit from the global economic recovery and overall consumption in emerging countries, Taiwan PCB industry in 2011 is expected to grow 29% global moving further into China cic advisory capacity analysis, according to a report in the printed circuit board industry in China under the situation of domestic growth and global capacity for transfer, will enter the high-speed growth period, by 2014, China's printed circuit board industry would rise to 41.92% of the total of the world's scale,
The gap with developed countries
China's printed circuit industry after nearly half a century of struggle, is China's electronic information industry has become the indispensable important foundation and the safeguard, the output value has been the world second, China's PCB output has reached 8.15 billion dollars in 2004, the total import and export for 8.9 billion dollars, it won't be long expected will rise as the world's first,
Our country is an electronic circuit, PCB production country, and now is far from the production of power, China also has the very big disparity compared with developed countries PCB industries,