You big, small white to come to for help, recently began to build their own home network, topology as shown in figure:
ROS DHCP allocation 192.168.50.102-255, gateway OpenWRT bypass by;
AC - 68 - u DHCP allocation 192.168.50.2-99, a gateway is oneself, 192.168.50.1;

The reason for this is as follows:
1. Temporarily don't want to run the cat bridge, I haven't prepared for the study of the IPTV, the first eyes light up the cat dial-up, ROS family routing, now 500/100 of the broadband can also run to 60 m/s download upload and 13 m/s, is quite satisfactory, light the cat DMZ ROS address, network access is also no problem;
2. Temporarily don't want to do AC - 68 - u AP, mainly food, worried about get ROS collapsed after being scold not mesh with, so there are at least two AC - 68 - u send wireless Internet use, ROS is also a virtual machine after all;

The question now is housed in the AC - 68 - u wireless devices, such as mobile phones and TV, there's no way to access the content on the server, under the ROS Emby server of what can only use port forwarding to the 192.168.1.2 instead to access, is not very convenient also cannot pass the data to each other, deliberately to unify the two part of the network segment, still can't access to each other?

Also tried the radio part is divided into 192.168.48.0/24 segments, and then respectively on ROS and AC - 68 - u write static route to the other side of the gateway:
192.168.50.0/24 - & gt; 192.168.1.2 instead
192.168.48.0/24 - & gt; 192.168.1.3
But I still can't, don't understand, turn off the firewall of asus, ROS firewall also what haven't set, but still can't,

Heavyweight directions,
Thank you very much!

CodePudding user response:

First of all, this topology is to use what you paint, painting good-looking?
Then, ROS and AC - 68 - u on the two routers (including light cat) actually, the wan port to the LAN port, not through a simple route to achieve, but before the in and out, do the NAT address translation, so the address of the LAN port, foreign are hidden, foreign address, only the wan port address,

CodePudding user response:

ROS DHCP and AC - 68 - u DHC is why two devices connected network in the same network segment (192.168.50. X), because it is in the same network segment, if AC68U connection devices to access the ROS of connected devices, because the network address is the same, then it won't put forward data through the gateway, think in the same local area network (LAN), but in fact you are in another network, because of you by 192.168.1. X put it off,

CodePudding user response:

The topology with what you paint

CodePudding user response:

The forehead is to use processon, very convenient on the web,

CodePudding user response:

reference weixin_40290083 reply: 3/f

ROS DHCP and AC - 68 - u DHC is why two devices connected network in the same network segment (192.168.50. X), because it is in the same network segment, if AC68U connection devices to access the ROS of connected devices, because the network address is the same, then it won't put forward data through the gateway, think, in the same local area network, but in fact you are in another network, because of you by 192.168.1. X to a separate it,

Well,, I change of AC68U into other, such as 48.0/24 is still won't do

CodePudding user response:

Not address within a segment is a local area network (LAN), you don't set the conflict, so why don't you all this from the main road by address? Wireless is simply do wireless, AC68 shut down the DHCP literally change a LAN address for managing equipment to the LAN port directly connect the router LAN port, wan mouth empty,

CodePudding user response:

I would also suggest that is wireless is not enabled DHCP, wireless after you do so much a NAT translation, such as the way by the way should be the cannot solve the problem, should the need to do port mapping,