IPv6 (Internet Protocol Version 6) is the second Generation of network layer Protocol standard Protocol, also known as the IPng (IP Next Generation), it is the Internet Engineering Task Force IETF (Internet Engineering Task Force) to design a set of specifications, is IPv4 (Internet Protocol Version 4) upgrade Version, number of IPv6 address claims to make every grain of sand all over the world an address,
Below we through an instance to recognize the first IPv6:
Configure the IPv6 address of the interface instance (in huawei S5700 switches for chestnut)
networking requirements 01
SwitchA and SwitchB through GE0/0/1 respectively, two switches GE0/0/1 are corresponding to the respective VLANIF10 interface, for VLANIF10 interface configuration IPv6 global unicast address, realize SwitchA and SwitchB Shared,
02 configuration ideas
Allocation IPv6 basis function is as follows:
1, enabling IPv6 on switches vlanif 10 interface functions,
2, 10 interface configuration valnif IPv6 global unicast address,
03 configuration steps
1, create a vlan 10, and divide the g1/0/1 interface of switches to vlan10;
SwitchA configuration:
The system - the view
[SwitchA] vlan
[SwitchA] interface GigabitEthernet0/0/1
SwitchA - GigabitEthernet0/0/1 port link -type trunk
SwitchA - GigabitEthernet0/0/1 port trunk allow - pass vlan 10
SwitchB configuration:
The system - the view
[SwitchB] vlan
[SwitchB] interface GigabitEthernet0/0/1
SwitchB - GigabitEthernet0/0/1 port link -type trunk
SwitchB - GigabitEthernet0/0/1 port trunk allow - pass vlan 10
2, enabling ipv6, global vlanif10 interface can make function of ipv6, and configure the global unicast address;
SwitchA configuration:
[SwitchA] ipv6
[SwitchA] interface Vlanif10
[SwitchA - Vlanif10] ipv6 enable
[SwitchA - Vlanif10] ipv6 address FC00:1: : 1/64
SwitchB configuration:
[SwitchB] ipv6
[SwitchB] interface Vlanif10
[SwitchB - Vlanif10] ipv6 enable
[SwitchB - Vlanif10] ipv6 address FC00:1: : 2/64
3, verify the configuration results;
If the configuration is successful, can view the configuration of the global unicast address, and the interface state to the Up, IPv6 status to Up, and you can look at the interface of neighbors,
# check SwitchA Vlanif 10 interface state;
# check SwitchB Vlanif 10 interface state;
# test between SwitchA and SwitchB connectivity;
welcome attention WeChat public number: learn some network
Every day we will bring you observe first-hand information and the depth of Internet industry, the most important thing is that there is cloud computing, data center, big data, data communication, network security, wireless, storage and other dry goods ~
Panoramic view of the Internet information, Internet is super interesting and practical case, etc.;
Learn some cheese | share cloud computing, big data, data communication, data center, security, wireless, storage and other knowledge;
Study club | share good books & amp; A good lesson, etc.;
The moonlight treasure box | share video learning, technical documentation, experience, etc.;
CodePudding user response:
Huawei S7706 switches the DHCP configuration, for exampleCodePudding user response:
Sharing is very detailed!!!!!!!!!!!!!CodePudding user response:
Still failed to understand the link local address and the essential difference between the global unicast addressCodePudding user response:
Link local address in the network ACTS as a gatewayGlobal public IP address is thin address
Problem is the PPPOE dial V6 PD or static PD,,,
PD you can down distribution, static, routing can be upwards, because you have to do operation business group
But how PPPOE issued to the address under layer 3 switches VLAN is a problem, pure two layers of good solution
CodePudding user response:
Hope people explainPPPOEv6 when assigned to PD two layers can define IP DHCP CLIENT PD XX to use this do stateless distribution
But three layers, the VLAN to do,,,, because every time PPPOE dial to get the PD is will change,,,,,,, can't change a set time, it's a nightmare for IPV6 address so far doesn't seem to support huawei cisco switches IPV6 passthrough mode