CMD/C program_flash - f E: \ ZYNQ_PRJ \ Z7_TEST0 \ UART_x8 \ FSBL \ BOOT3 bin - offset 0 - flash_type \
Qspi_single - FSBL E: \ ZYNQ_PRJ \ Z7_TEST0 \ UART_x8 \ UART_x8 SDK \ FSBL \ Debug \ FSBL elf - cable type \
Xilinx_tcf url TCP: 127.0.0.1:3121
* * * * * * Xilinx Program Flash
* * * * * * Program Flash v2018.1 (64 - bit)
* * * * SW Build 2188600 on Wed Apr 4 18:40:38 MDT 2018
Xilinx * * Copyright 1986-2018, Inc. All Rights Reserved.
Connected to hw_server @ TCP: 127.0.0.1:3121
The Available targets and devices:
Target 0: JSN - DLC9LP - 00000000000000
Device 0: JSN ba00477 DLC9LP - 00000000000000-4-0
Retrieving the Flash info...
Initialization done, programming the memory
=====MRD - & gt; Addr=0 xf800025c, data=https://bbs.csdn.net/topics/0x00000001=====
BOOT_MODE REG=0 x00000001
WARNING: [Xicom 50-100] The current boot mode is QSPI.
If the flash programming fails, configure device for the JTAG boot mode and try again.
=====MRD - & gt; Addr=0 xf8007080, data=https://bbs.csdn.net/topics/0x30800100=====
=====MRD - & gt; Addr=0 xf8000b18, data=https://bbs.csdn.net/topics/0x00000000=====
Downloading FSBL...
Running FSBL...
Finished running FSBL.
=====MRD - & gt; Addr=0 xf8000110, data=https://bbs.csdn.net/topics/0x000FA220=====
READ: ARM_PLL_CFG x000fa220 xf8000110 (0)=0
=====MRD - & gt; Addr=0 xf8000100, data=https://bbs.csdn.net/topics/0x00028008=====
READ: ARM_PLL_CTRL x00028008 xf8000100 (0)=0
=====MRD - & gt; Addr=0 xf8000120, data=https://bbs.csdn.net/topics/0x1F000200=====
READ: ARM_CLK_CTRL x1f000200 xf8000120 (0)=0
=====MRD - & gt; Addr=0 xf8000118, data=https://bbs.csdn.net/topics/0x000FA240=====
READ: IO_PLL_CFG x000fa240 xf8000118 (0)=0
=====MRD - & gt; Addr=0 xf8000108, data=https://bbs.csdn.net/topics/0x00030008=====
READ: IO_PLL_CTRL x00030008 xf8000108 (0)=0
Info: 256 KB of Remapping on - chip - the memory RAM memory to 0 xfffc0000.
=====MRD - & gt; Addr=0 xf8000008, data=https://bbs.csdn.net/topics/0x00000000=====
=====MWR - & gt; Addr=0 xf8000008, data=https://bbs.csdn.net/topics/0x0000DF0D=====
MASKWRITE: addr=0 xf8000008, mask=0 x0000ffff, newData=https://bbs.csdn.net/topics/0x0000DF0D
=====MWR - & gt; Addr=0 xf8000910, data=https://bbs.csdn.net/topics/0x000001FF=====
=====MRD - & gt; Addr=0 xf8000004, data=https://bbs.csdn.net/topics/0x00000000=====
=====MWR - & gt; Addr=0 xf8000004, data=https://bbs.csdn.net/topics/0x0000767B=====
MASKWRITE: addr=0 xf8000004, mask=0 x0000ffff, newData=https://bbs.csdn.net/topics/0x0000767B
Problem in running uboot
Flash programming initialization failed.
ERROR: Flash Operation Failed
CodePudding user response:
Have you found the solution?CodePudding user response:
Empty FLASH, for the first time to use first, benefiting pin configuration model of JTAG burning program, after the success of the burn, benefiting to QSPI mode